Description :

XM-RM781 is a 4 x 10/100/1000 Mbps Rapid-Matrix UTP Ethernet test module.
1. Saving valuable time and expenses while testing for network product designs and quality control in mass-production scale, XM-RM series modules provide a flexible, reliable, and high-precision solution.
2. Specifically designed for NuStreams chassis (such as NuStreams-2000i and Nustreams-600i), XM-RM series modules supports hot swap, multi-user operation, and Rapid- Matrix, a technology that can generate multi-stream traffic simultaneously with different kinds of frames/packets with almost any required protocol headers, tags and payload for each port.
3. XM-RM series can be divided into Standard and Professional types. The advantage of Standard XM-RM series is that there are more test ports on each module. The cost per test port is lower for mass-production scale DUT tests. Having similar features like Professional XM-RM series, Standard XM-RM series, with less capacity, provide reliable DUT test results at mass-production line.
4. NuStreams-2000i and NuStreams-600i chassis with XM-RM Series test module cards can perform synchronized tests to ensure the test precision. Also, the time consumed for all DUTs’ multi-task testing will be shortened dramatically.
5. Along with the advanced technology mentioned above, Xtramus also provides several software applications, such as NuWIN-RM, APMPT-4, and other ongoing softwares complied with RFC-2544, RFC-2889 and etc. XM-RM series can test the network equipments in conformance, performance and stress tests.

Specification :

1. Interface: (1) Gigabit Ethernet (10/100/1000BASE-T): UTP port x 4. (2) Module port for connection to NuStreams Chassis. 2. LED Indicator: SYS, L/A (Link/Active): 1, 2, 3, 4. 3. Speed and mode: (1) Auto Negotiation / forced mode. (2) 10/100Mbps half / full duplex. (3) 1000Mbps full duplex. 4. Frame Length: Tx Packet Length: 48 ~ 2Kbytes. 5. Applications: (1) Test module for Gigabit Ethernet device. (2) Test module for quality control of network device in mass production line. (3) Test module for new design network product in R&D laboratory that need report of precise statistics and result. (4) Apply to Telecommunication room, R&D laboratory, Data center, etc. 6. Capture Criteria: SDFR (self-discover filtering rules) technique is able to capture packets by different criteria in either a unique value or a range of values by user-friendly UI. (1) MAC layer event. (2) Network layer event. (3) SDFR Pattern (set). (4) 2nd level CRC.

Features :

1. Supports 10/100/1000 Mbps Ethernet test equipment.
2. Wirespeed hardware based traffic generation and analysis.
3. High test performance with low-cost testing ports.
4. Stream based wire speed layer2~3 traffic load generation.
5. RFC 2544/2889 test suite.
6. Wirespeed traffic capture with programmable filter and trigger criteria.
7. High-precision performance measurement of throughput, latency, loss, sequence and mis-ordering error.
8. Remote management of testpoints.
9. Validation with negative and abnormal test conditions per packet byte.
10. Real-time statistics for each port, including transmitted/received frame for VLAN, IPv4, IPv4 fragment, IPv4 extension , ICMP, ARP, total bytes/packets, CRC, IPCS error and over-and-under size frames.

• 
  Rapid Matrix Modules
• 
  Rapid Matrix Modules
• 
  Burst Mode Matrix Modules
• 
  Burst Mode Matrix Modules
• 
  Burst Mode Matrix Modules
• 
  Burst Mode Matrix Modules
• 
  Burst Mode Matrix Modules
• 
  Burst Mode Matrix Modules

More