Xtramus Technologies
Taiwan Manufacturers, Exporters.
Detail Information
Description :
XM-RM671 is 4 Ports 100 Mbps POF Ethernet test module with high test quality & reliable test result.
1. POF interface is an inexpensive solution when it compare with glass fiber that has expensive total cost. The distance for transmission is up to 100 meter with no generation of electromagnetic radiation and also free of electromagnetic interference, crosstalk and noise. Request of high-speed and low cost home networking is possible by POF.
2. XM-RM series is divided into Standard and Professional types. The advantage of Standard XM-RM series is that there are more test ports on each module. The cost per test port is lower for mass production test of DUT. Standard XM-RM series provide the same features as professional XM-RM series with less capacity; however, they provide reliable test result for test of DUT at mass product line.
3. Rapid-Matrix is a technique that can generate multi-streams traffic simultaneously with different kinds of frames/packets with almost any required protocol headers, tags and payload for each port, which is quite helpful for mass production test.
4. Unlike traditional test procedure at other test equipment, NuStreams-2000i and NuStreams-600i chassis with XM-RM series module cards are able to perform global command that actives multi-task tests to DUTs simultaneously. This mechanism synchronizes the test procedure to all devices under test; hence, the test duration of multi-task tests for all DUTs is reduced dramatically.
5. The SDFR (self-discover filtering rules) technique is able to capture packets by different criteria in either a unique value or a range of values by user-friendly UI, such as a MAC address or MAC addresses in specified range, and also shows the statistics in real-time.
6. Along with the advanced technology above, Xtramus provides several software applications such as NuWIN-RM, APMPT-4, and other ongoing software for XM-RM series that can test the network equipment in conformance, performance and stress purpose.
Specification :
1. Interface: (1). 100Mbps Fast Ethernet: Optolock POF port x 4 (2). Module port for connection to NuStreams Chassis. 2. LED Indicator: SYS, L/A (Link/Active): 1, 2, 3, 4. 3. Speed and Mode: (1) Auto Negotiation / Forced Mode. (2) 10/100Mbps Half / Full Duplex. 4. Frame Length: Tx Packet Length: 48 ~ 2Kbytes. 5. Applications: (1) Test module for Fast Ethernet POF device. (2) Test module for quality control of network device in mass production line. (3) Test module for new design network product in R&D laboratory that need report of precise statistics and result. (4) Apply to Telecommunication room, R&D laboratory, Data center, etc. 6. Capture Criteria: SDFR (self-discover filtering rules) technique is able to capture packets by different criteria in either a unique value or a range of values by user-friendly UI. (1) MAC Layer Event: 5. (2) Network Layer Event: 3. (3) SDFR Pattern (set): 2. (4) 2nd level CRC: Support.
Features :
1. Supports 10/100/1000 Mbps Ethernet test equipment.
2. Wirespeed hardware based traffic generation and analysis.
3. High test performance with low-cost testing ports.
4. Stream based wire speed layer2~3 traffic load generation
5. RFC 2544/2889 test suite.
6. Wirespeed traffic capture with programmable filter and trigger criteria.
7. High-precision performance measurement of throughput, latency, loss, sequence and mis-ordering error.
8. Remote management of testpoints.
9. Validation with negative and abnormal test conditions per packet byte.
10. Real-time statistics for each port, including transmitted/received frame for VLAN, IPv4, IPv4 fragment, IPv4 extension , ICMP, ARP, total bytes/packets, CRC, IPCS error and over-and-under size frames.
Xtramus Technologies
- Taiwan